![will lathe and plaster walls hold shelf will lathe and plaster walls hold shelf](https://drilling-it.com/wp-content/uploads/2022/02/how-to-hang-shelves-on-plaster-walls-1-1-683x1024.jpg)
Here is a list of items you’ll need before you begin hanging your shelf on a plaster wall:įor safety, stability and a long-standing shelf, we highly recommend that you drill holes into your wall – not just into the plaster, but into timber studs. Make your home the best it can possibly be, with our high quality and rigorously-tested brackets. Here is our definitive guide to hanging a shelf on a plaster wall.Īt Carinya, we support DIY home improvements. In small living spaces, hanging shelves can be instrumental in creating functional rooms that save on space.
![will lathe and plaster walls hold shelf will lathe and plaster walls hold shelf](https://i.pinimg.com/originals/fc/9d/2c/fc9d2c307badf6c6d1927fdcff7e7ac3.jpg)
While these changes may not come into effect until 2020, there’s plenty of exciting options on the horizon for low impact home improvement. Rental laws in Victoria have changed, allowing renters more scope for decorating. The bracket can be fixed with screws through the spacer into plugs in the blockwork, or the spacer can be screwed to the blockwork and then shorter screws used to fix the bracket.The most efficient way for mounting shelves on plaster walls How to hang a shelf on plaster walls The cut-outs and spacers can be small so that the bracket or batten cover them, or large - although 'large' is less fiddley, it is harder to blend it in with the rest of the wall. Make and fit spacers which can be tightened down onto the blockwork behind the plasterboard.Cut out the plasterboard at these points.Any attempt to pull down a bracket onto the unsupported surface will cause the lasterboard to deform. Dry Lining walls.ĭry lining is possibly the most difficult type of wall to get a strong fixing as the surface plasterboard is only supported by 'blobs' of adhesive. Drill clearance holes through the lathe and plaster so that these are not subjected to excessive sideways pressure as the screw is fitted. Lathe and plaster walls may crack when a bracket is tightened down onto the surface as the lathes are compressed.
![will lathe and plaster walls hold shelf will lathe and plaster walls hold shelf](https://leftshoreconstruction.com/wp-content/uploads/2020/06/1-4-1-Lath-and-Plaster-4-1024x658.jpg)
Once the first stud has been located, measure along the line in multiples of 405mm (16 inches) and drill through to confirm the location of the next stud - if further studs cannot be located in this way, the only option is to drill another series of small holes until a stud is found. When all else fails, the last resort is to draw a horizontal line where the shelf is required and to drill small holes along the line about 25mm (1 inch) apart until solid timber (i.e. It is not so easy to locate the studs holding up lathe and plaster finishes as there is no discernible difference in the sound of a knock. To find the position of the studs behind plasterboard, lightly knock on the wall while moving sideways - the studs should sound solid while the spaces between should sound hollow. The studs are normally set at equal distances apart - on older stud walls they are usually no greater than 405mm (16 inches) apart, while in more modern stud walls, the maximum spacing is about 600mm (24 inches). Stud walling (both lathe and plaster and plasterboard).įix shelving just to the plasterboard (or lathe and plaster), strong fixings can only be achieved when fixings are screwed directly into the vertical timbers (the studs). Some blocks (such as modern high insulation types) are extremely soft, always drill these carefully to avoid over-enlarging the hole and use the special wall plugs. To overcome this, an option is to fix a batten to the surface of the plaster and then screw shorter fixings for the brackets into this batten. Some clay bricks (mainly old ones) and true concrete blocks contain hard pieces (flints etc) which can cause a drill bit to run off line - this can result in the bracket holes not lining up or the shelf not being level. Plaster alone is not strong enough to hold wall plugs, so the holes (and plugs, screws) need to be long enough to go through the plaster into the brick or block work.Īnother weak point may be the mortar joints between the bricks/blocks, especially where lime mortar has been used - it is best to locate the fixing so that the fixing holes go into actual brick/block rather than the mortar joints. Strong fixings can be easily made on most masonry walls just by using screws and wall plugs - for extremely heavy loads wall bolts can be used.
![will lathe and plaster walls hold shelf will lathe and plaster walls hold shelf](https://i.redd.it/0ujzcoq0yfqz.jpg)
for brackets) can be made to them, below we give suggestions for making strong fixings to masonry plaster, stud walling, plasterboard dry lining walls. Which type of wall you have, will affect how strong fixings (i.e. A number of different types of internal wall will be found masonry plaster, stud wall (either plasterboard or lathe and plaster), plasterboard dry lining - see our page which explains these different types of wall.